Wishon Golf’s 310MG wedges combine a traditional blade profile with an innovative straight leading edge and undercut beveled sole to offer players a series of wedges which are far easier to line up.
Enhancing the performance of the 310MG wedges are Wishon Golf’s proprietary Micro-Grooves which puts 40% more scoreline edges on the surface of the ball than conventional wider grooves for increasing backspin. The unique undercut beveled sole features a pronounced narrow area of increased bounce at the very front of the sole which greatly reduces the chance of digging the leading edge or hitting fat shots.
- Unique straight leading edge profile contrasts the usual curved leading edge on all other wedges to offer ease in alignment for improved shot accuracy.
- Undercut beveled front of sole prevents digging with the leading edge from fairway, rough and sand to allow the sole to clear through the turf smoothly, even on pronounced hands-forward knock down shots.
- Wishon Golf’s unique Micro Groove scorelines at 0.6mm width X 2.1mm spacing contrasts to normal groove specs of 0.8mm width X 2.8mm spacing to put the edges of 5 lines on the surface of the ball at impact compared with only 3 from usual scorelines. More lines on the ball means channeling away more moisture from the contact of face and ball to reduce the chance of a flyer or slider shot.
- Low 1mm offset combined with straight leading edge allows the 310MG wedges to build confidence in the ability to hit accurate shots into the greens.
© COPYRIGHT 2025 WISHON GOLF
Hi, why was the 310 design without the milling on the face? Is it to do with regulations or is it just a design preference? I’ve got the 310’s in the bag and very happy but just wondering as I’ve really enjoyed previous models with the milling. Thanks
Pete I was designing what became the 309 and the 310 at the same time so I just decided to do the one with the normal scorelines with the milling but no on the one with my Micro Grooves. Both are USGA/R&A conforming. The USGA has been cracking down a bit on face milling on wedges so some of the older milled face wedges that happened to slip by the USGA will make a pretty big difference in terms of friction and spin! The rule says the distance from the peak to the trough of a milling groove cannot be… Read more »
Hi Tom,
Does the 310MG have the Zero bounce heel like the HM micro groove wedge
Thanks
DAVE
Yes, the 310 has a zero bounce sole design at the heel end of the sole. I think every wedge I may ever design going forward will incorporate this feature because it never detracts from any other performance elements in a wedge and it can help when you roll the face open to keep the leading edge from rising up and potentially getting in the way of impact.
TOM
How does the “undercut beveled front of sole” in the description of the 310MG compare to the “Front sole Knock Down grind” in the description for the Micro-Groove HM wedges? I need to replace my wedges and was sad to hear the HMs have been discontinued.
ED
This is basically just using a little different terminology to describe a similar sole grind situation between those two wedge models. However the grind on the HM looks a little different than the grind on the 310MG even though they are both intended to do the same thing – to offer more bounce on the very front part of the sole so as to help reduce the severity of the sole digging into the turf when the player hits a shot with the hands well forward at impact.
TOM
Hi Tom , is the face milling a circular pattern? Thanks
Hello, and thank you for the great products and all the excellent information you provide on your website. I am 68 years old, 18 handicap, and my driver swing speed tops out at 80 mph. My irons have stock Callaway RCH 65i graphite shafts in light flex. I am interested in Callaway CB wedges, but rather than the stock graphite shaft (Project X Catalyst 65 Wedge, only available in R flex), the rep said to go with the same shaft as my irons. Is that a good idea? Wondering what your thoughts are…given my level of ability, does it matter one… Read more »
KEN Having been in clubhead design since 1986 and shaft design and analysis since 1997, I have never found a truly viable reason for there to ever be separate shafts for wedges. Wedge shafts are always the stiffest of all shafts in the set because they are the shortest, and because they have to match with wedge heads which are always the heaviest clubheads in the set. Quite simply, wedge shafts do not bend anywhere near as much as do other shaft in the set. And with so much loft on wedges anyway, there can’t really be any measurable contribution… Read more »
Just wanted to compliment you on these great new wedges Tom. Put them play today for the first time (50°, 55° & 60°). Built them with the knockdown wedge shaft and they feel amazing, especially the 55° which is a club I use quite a lot. I play on firm links turf and the club just glided through the turf beautifully and had awesome control and spin. I’ll definitely get these again once I wear these out.
CRAIG
Thanks very much for your kind comments on the new 310 wedges. That always makes me really pleased to hear when a player likes a model that I had the chance to design! May they always behave themselves for you!
TOM
Tom,
I have been loving the new designs and this is no different. I do have a silly question, so don’t beat me up to bad in the answer.
With the squared edge, can you or should you open the clubface like the rounded wedges on certain shots? How would that change the idea behind the leading edge profile?
Thank you for all the great clubs,
Jim
JIM Sure thing, no problem with opening up the face of the 310MG wedges, even though they are designed with a bit more of a straight leading edge from toe to heel. It might look a little different than opening up a wedge with a rounded leading edge profile, but then too, even on other wedges, when you have the face open you know the face is pointing to the right. You just make sure the swing path is at the intended target and everything works out fine. And to allow for spin causing the shot to often jump a… Read more »